Showing 1–16 of 17 results
This plug-n-play adapter lets you connect your AdMore light kit (or any other lighting accessory with less than a 2A current draw) without having to tap the stock wiring on your Yamaha FJR (Gen II & Gen III).
Click Here for Click’n’Ride Socket What’s in the box? 1 socket with wiring (bullet ends) 1 rubber Moisture Guard plug 1 nylon spacers (1mm) 1 nylon spacer (2mm)
What’s in the box? (x1) Wiring Adapter
This DENALI T3 wiring harness kit features high-quality waterproof components and is designed to power four DENALI T3 Light Pods. It features low profile, water tight connectors and high quality molded wire to ensure moisture is kept out of the system. The harness includes 3-position switch to change the T3s pods between color 1, color 2 or…
What’s in the Box: (1) 48in B6 & DRL Harness Extension
This DENALI DRL wiring harness kit features high-quality waterproof components and is designed to power two DENALI DRL Light Pods (NOT compatible with 2.0 Denali Light Pods). It features low profile watertight connectors and high-quality molded wire to ensure moisture is kept out of the system. The harness includes a completely sealed waterproof switch that…
The DENALI Control Switch enables complete control of the KTM CANsmart light circuits. Both Auxiliary Light Set One and Auxiliary Lights Set Two can be independently toggled ON/OFF and adjusted to the desired intensity via the switch. The kit includes a 7/8″ mounting band which is used to attached the control switch to your handlebar…
Use the DENALI wiring adapter for connecting DENALI B6 LED Brake Lights to the OEM KTM harness for a true plug & play connection. No wire tapping or other modifications to the original harness are necessary, just plug directly into the factory connector to send the brake light signal from your motorcycle to the B6…
This wiring adapter enables plug-&-play connection between our standard DialDim Lighting Controller and the Ducati DesertX. To install, simply connect the white connector to our DialDim Controller and the remaining connectors in line at the DesertX headlight, horn, and turn signal connectors. Click to learn about all of the innovative features and settings in our DialDim Lighting Controller. Instruction Manual…
The standard harness also features DENALI’s clever HotSwap™ design that enables an effortless swap from the standard single-intensity relay to our Dual-Intensity DataDim™ Controller. (sold separately) Plug in DENALI’s to enable the DENALI lights to switch between half and full intensity with your vehicle’s original high beam switch.
Use the DENALI wiring adapter for connecting T3s to the GEN II CANsmart Controller for a true plug & play connection. Compatible with all GEN II DENALI CANsmart Controllers, no wire tapping or other modifications are necessary, just plug directly into the circuits of the CANsmart to send the signals from your controller to the T3 Lights. This harness…
Use this DENALI T3 Wiring Adapter for plug and play connection of DENALI Front T3 Lights to Harley-Davidson Motorcycles. The adapter simply plugs inline between the factory front turn signals.
The long-awaited Trigger Wizard is a simple wiring adapter that converts a ground-switched vehicle high beam wire to a traditional high beam wire that outputs 12 volts when you turn on your high beam. This adapter is required if you want to output a 12v high beam signal that will allow DENALI lights to change intensity with your…
Turn load resistors are necessary to prevent hyper flashing of the signals when swapping from incandescent to LED turns signals. Use these 10 Ohm Load Resistors to replace your original 21 Watt Turn Signals with DENALI Please Note: You will need one resistor for each turn signal being installed to the motorcycle. (Sold in pairs)…
This wiring adapter plugs in-line at the factory turn signal connectors to enable plug-&-play connection of aftermarket turn signals to the Ducati DesertX. The green wire provides the turn signal output and the black wire is ground. If you are installing DENALI switchback turn signals, use the included posilocks to connect the black and green wires to the…
Note: We highly recommend buying this product when purchasing LED micro / mini indicators in order to save any disappointment when fitting. NO wire cutting or soldering is required these resistors fit inline.
No products in the cart.
